Home > Frame Relay Tutorial

Frame Relay Tutorial

September 7th, 2011 Go to comments

Note: Frame Relay is no longer a topic in CCNAv3 200-125 exam.

Let’s start this article with the question: Why do we need Frame Relay?

Let’s take a simple example. Suppose you are working in a big company and your company has just expanded to two new locations. The main site is connected to two branch offices, named Branch 1 & Branch 2 and your boss wants these two branches can communicate with the main site. The most simple solution is to connect them directly (called a leased line) as shown below:

Frame_Relay_before_using_Frame_Relay.jpg

To connect to these two branches, the main site router, HeadQuarter, requires two serial interfaces which a router can provide. But what happens when the company expands to 10 branches, 50 branches? For each point-to-point line, HeadQuarter needs a separate physical serial interface (and maybe a separate CSU/DSU if it is not integrated into the WAN card). As you can imagine, it will need many routers with many interfaces and lots of rack space for the routers and CSU/DSUs. Maybe we should use another solution for this problem? Luckily, Frame Relay can do it!

By using Frame Relay we only need one serial interface at the HeadQuarter to connect to all branches. This is also true when we expand to 10 or 50 branches. Moreover, the cost is much lesser than using leased-lines.

Frame_Relay_implement_Frame_Relay.jpg

Frame Relay is a high-performance WAN protocol that operates at the physical and data link layers of the OSI reference model. It offers lower-cost data transfer when compared to typical point-to-point applications, by using virtual connections within the frame relay network and by combining those connections into a single physical connection at each location. Frame relay providers use a frame relay switch to route the data on each virtual circuit to the appropriate destination.

Maybe these terminologies of Frame Relay are difficult to understand so we will explain them in more detail in this article.

DCE & DTE

The first concept in Frame Relay you must grasp is about DTE & DCE:

+ Data terminal equipment (DTE), which is actually the user device and the logical Frame-relay end-system
+ Data communication equipment (DCE, also called data circuit-terminating equipment), which consists of modem and packet switch

In general, the routers are considered DTE, and the Frame Relay switches are DCE. The purpose of DCE equipment is to provide clocking and switching services in a network. In our example, HeadQuarter, Branch 1 & Branch 2 are DTEs while Frame Relay switches are DCEs.

Virtual Circuits

The logical connection through the Frame Relay network between two DTEs is called a virtual circuit (VC). The term “virtual” here means that the two DTEs are not connected directly but through a network. For example, the HeadQuarter & Branch 1 (or Branch 2) can communicate with each other as if they were directly connected but in fact they are connected through a Frame Relay network with many Frame Relay switches between them.

Frame_Relay_virtual_circuit.jpg

There are two types of VCs
+ switched virtual circuits (SVCs): are temporary connections that are only used when there is sporadic data transfer between DTE devices across the Frame Relay network. SVC is set up dynamically when needed. SVC connections require call setup and termination for each connection.
+ permanent virtual circuits (PVCs): A predefined VC. A PVC can be equated to a leased line in concept.

Nowadays most service providers offer PVC service only to save additional costs for signaling and billing procedures.

Comments (11) Comments
Comment pages
1 7 8 9 817
  1. exam 210-065
    July 18th, 2017

    I have been struggling with this new video/voice collaboration exam. Does anyone have any good info on the test? Study questions, etc?

  2. `
    October 5th, 2017

    gfdsa23erfgbhnm

  3. sanjay desai
    March 15th, 2018

    very good explained.

  4. adamedz
    May 15th, 2018

    thanks vry much

  5. Anonymous
    June 6th, 2018

    Great work.. very usefull

  6. Time Traveler
    October 23rd, 2018

    Can someone explain what CLOCKING really means and why we need it? Thank you…

  7. Andrew
    January 30th, 2019

    Well explained.Kudos to the author. Keep up the great work!

  8. Anonymous
    February 25th, 2019

    .

  9. Frame Relay
    March 20th, 2019

    Excellent explanation

  10. Vutha
    December 3rd, 2019

    Dear All

    Does CCNA Routing and Swithing Still has Frame Relay topic?

  11. Anonymous
    December 17th, 2019

    Thank you! This information is very hard to find on the Internet

Comment pages
1 7 8 9 817
Add a Comment