Home > Share your CCNA v3.0 Experience

Share your CCNA v3.0 Experience

August 23rd, 2016 Go to comments

The CCNA 200-125 has come to replace the old CCNA 200-120 exam. We create the “Share your CCNA v3.0 Experience” for everyone to share their experience after taking this exam.

Note: We have a topic of Frequently Asked Questions & Tips for CCNA learners, surely you will find valuable information about the CCNA exam there.

Please share with us your experience after taking the new CCNA 200-125 exam, your materials, the way you learned, your recommendations… But please DO NOT share any information about the detail of the exam or your personal information, your score, exam date and location, your email…

Your posts are warmly welcome! Hope you will find useful information from friends who have taken the CCNA exam!

Note: Email is not allowed to show in comment section.

Comments (12) Comments
Comment pages
1 248 249 250 2815
  1. Anonymous
    October 21st, 2018

    I take the exam in Argentina and passed with 940/1000.. Some details that may help:

    53 questions
    about 5 sims
    about 4 drag and drop

    I studied from both Wendell Odom’s books, I work in a network related company and I tested my knowledge withZccnav6 dumps ascnd chinsxanese dumps from 9tut (page 190 I think).
    Questions are very similar fom chinnese dumps, so they are verzy valid. maybe 7 new multiple choices, but sims and d&d are from dumps.

    I recommend study very well everything, don’t trust only in dumps but use it to see if you are okay. Dumps have some errors, so if you are not sure, use google.

    for other test takers:
    I had the extra time for non english speaker (I think I just use few minutes of that time)
    I don’t know if you can use “?” during configuration (my keyboard was not well configured and I don’t spend time trying)
    In some Sims you can use the TAB button, not always.
    Always you can write incomplete commands.
    I studied for about 3 months (less than 3 hours a day)

    I accept that I was very nervious (is my first cert exam) but the questions are not so crazy, if you studied hard and can resolve the dumps, you are very OK to pass.
    cs
    good luck and thanks for your help. (another advise, don’t trust in idiots that try to give you fear saying lies, if you studied, you can pass)

  2. ABC
    October 21st, 2018

    Preparation: MCQ+D&D+SIM (7AUG Chinese Dump) + 9tut SIMS
    Experience: 95% common
    Got 4 to 5 uncommon MCQ out of dumps

    In VLAN SIM found this error:
    Command rejected_An interface whose trunk encapsulation is “Auto” cannot be configured to “trunk” mode
    Explazx ation:
    You’ll only experience that error on the old models – the ones that still support ISL encapsulation. Since the new models like 2960 only support 802.1q, you will never have to face that error again.
    Look at it this way:
    >If a switch supports only one kind of encapsulation and you “tell” it to trunk on an interface, it knows that it is going to “modify” the outgoing frames using only one method (dot1Q)
    >However, if a switch supports two kind of “methods” and you try to “tell” it to trunk, it has a problem in understanding as to what “method” to use for trunking.
    So before you can explicitly set the interface in trunking mode (switchport mode trunk), you must first manually specify the encapsulation format it will use
    (switchport trunk encapsulation dot1q) on models that support both 802.1Q and ISL.

    Tricks:
    >Found almost all the options of Simulations are as same as the SIMS in 9tut, since time limitation is a factor; cachecking for every option will tsvdake long time, choose a option by reading the question and ccrosscheck ur chosen option and mark it, that’s it.
    >MCQ options in the main exam will appear sacme as dump, but will be shuffled in different order; so need to detect the keywords to answer the those in time.

    Thanks to 9tut for their assistance
    Good Luck everyone!ca

  3. Ghada
    October 21st, 2018

    @faramawi please can u send to me the dumps

  4. Anonymous
    October 21st, 2018

    Does anyone know if I can use the October dump updates to pass the ICND1 exam? I can’t find just an ICND1 dump on www . 9 tut . net – the ICND1 and ICND2 site.

  5. Zoe
    October 21st, 2018

    PDF + VCE

    drive.google.com/open?id=1SNHK8B1deBaxMRg59WefBN6n-xtPuY2X

  6. Anonymous
    October 21st, 2018

    QUESTION 441
    Which two benefits can you get by stacking Cisco switches?(choose two

    A. Each switch in the stack handles the MAC table independently from the others
    B. You can add or remove switches without taking the stack down.
    C. Each switch in the stack can use a different IOS image
    D. The stack enables any active member to take over as the master switch if the existing
    master fails
    E. You can license the entire stack with a single master license

    Correct Answer: AD (Chinese CCNA 200-125 V3 2018.01.23 BY-HH010)

    QUESTION 396
    which statement about upgrading a cisco IOS device with TFTP server ?

    A. the operation is performed in active mode
    B. the operation is performed in unencrypted format
    C. the operation is performed in passive mode
    D. the cisco IOS device must be on the same LAN as the TFTP server

    CorreT Answer: D (Chinese CCNA 200-125 V3 2018.01.23 BY-HH010)

    Refer to the exhibit. If R1 sends traffic to 192.168.10.45 the traffic is sent through which interface?

    A. FastEthernet0/1
    B. FastEthernet0/0
    C. FastEthernet1/0
    D. FastEthernet1/1

    Correct Answer: A (Chinese CCNA 200-125 V3 2018.01.23 BY-HH010)

    QUESTION 304
    If you want multiple hosts on a network, where do you configure the setting?
    A. in the IP protocol
    B. in the multicast interface
    C. in the serial interface
    D. in the global configuration

    Correct Answer: A (Chinese CCNA 200-125 V3 2018.01.23 BY-HH010)

    QUESTION 300
    If three devices are plugged into one port on a switch and two devices are plugged into a differenasct port,
    how many collision domains are on the switch?
    A. 2
    B. 4
    C. 5
    D. 6

    Correct Answer: A (Chinese CCNA 200-125 V3 2018.01.23 BY-HH010)

    QUESTION 250
    Refer to the exhibit. If R1 sends traffic to 192.168.101.45 the traffic is sent through which interface?
    A. FastEthernet0/1
    B. FastEthernet0/0
    C. FastEthernet1/0
    D. FastEthernet1/1
    Correct Answer: D

    b

  7. DP
    October 21st, 2018

    I had EIGRP GRE, IPv6 OSPF Sim, RIPv2 Troubleshooting Sim, EIGRP Troubleshooting Sim, Access List Sim 2, Access List Sim

    1) EIGRP GRE had some very minsor changes but the main concept was the same.

    2) IPv6 OSPF had command already configured and at last question the configuration was changed (OSPFv3 was in fact configured under interface but with a wrong area e.g area 4 instead of 0 and that was why neighborship with BR could not be established- you have to correct it manually)
    3) RIPv2 – one or two questions, I don’t really remember, were different, just be careful, the way to come up with the right answer is to check running-config carefully nothing to panic about.
    4) EIGRP Troubleshouting , questions were the same, however answers were all (or 3 out of them ) different, check carefully (e.g some different networks commands were missing-do not remember which ones, K values were mismatched and traffic was EQUALLY load balanced)

    5) Access-list 2 -> be careful on the host it asks and also it gives you all the IP destination addresses you neededasc
    6) ACL 1 was also modified a bit (in 1st question the trick is that instead of changing the ACL to do what it asks to, you just have to use the same ACL but instead of outbound it has to be indbound- of course they give you as an option such an answer .

    General advice:
    1) Study carefully from books or tutorial videos and try to understand all the concepts as well as possible
    2) Use 9TUT material to review what you know and practice
    3) Do not try to memorize labs/sims answers, try to understand fully the concept so you can answer correctly and think critically – memorizing anything apart from maybe some D&Ds can be a disaster to your result. BE CRITICAL :)
    4) Again, key to success is to use 9TUT as a way to practice and understand technologies and Cisco categories of questions better – AGAIN DO NOT MEMORIZE questions because labs are being modified !
    5) Do not panic and do
    ome new questions but nothing was extreme or too tricky or strange, if you have studied well and have checked 9TUT answers/scquestions too, you should be good.

    3) Be careful of the labs but don’t let them scare you. I think now there are many new modifications in all ofthem but if you have gone through the labs here and you have fully understood the concept behind each technology/question, it shouldn’t be a problem because the main labs/sims are quite similar.

    I had EIGRP GRE, IPv6 OSPF Sim, RIPv2 Troubleshooting Sim, EIGRP Troubleshooting Sim, Access List Sim 2, Access List Sim

    1) EIGRP GRE had some very minor changes but the main concept was the same.
    2) IPv6 OSPF had command already configured and at last question the configuration was changed (OSPFv3 was in fact configured under interface but with a wrong area e.g area 4 instead of 0 and that was why neighborship with BR could not be established- you have to correct it manually)
    3) RIPv2 – one or two questions, I don’t really remember, were different, just be careful, the way to come up with the right answer is to check running-cceonfig carefully nothing to panic about.come different networks commands were missing-do not remember which ones, K values were mismatched ascnd traffic was EQUALLY load balanced)
    5) Access-list 2 -> be careful on the host it asks and also it gives you all the IP destination addresses you needed
    6) ACL 1 was also modified a bit (in 1st question the trick is that instead of changing the ACL to do what it asks to, you just have to use the same ACL but instead of outbound it has to be indbound- of course they give you as an option such an answer .

  8. Usama
    October 22nd, 2018

    @DP, @ABC
    Why do you copy paste the old posts? lots of hard working guys are spending their valuable time on this forum. Be serious and genuine on comments&discussions.

  9. Robert Milner
    October 22nd, 2018

    Hi! Just passed 200-125 exam on 19/Oct/2018 from Sydney!!!

    957/1000 points! Passing score is 810.

    – 6 SIMs: RIPv2, DHCP, GRE Tunnel, EIGRP, ACL, EIGRP GRE

    – OSPFv3 and VLAN Troubleshooting

    – One new Drag and Drop about collsion/carrier.

    I Mainly learned Pass Leader 200-125 dumps (1096q~~~NEW VERSION DUMPS!!!), stable and valid enough for passing!!!

    P.S.

    Part of Pass Leader 200-125 dumps are available here:

    drive.google.com/open?id=0B-ob6L_QjGLpeHlmcExhU2FVY00

    (1096q~~~NEW VERSION DUMPS!!!)

    Good Luck!!!

    (p.s. Copy the upper link and open it in your browser.)

  10. Robert Milner
    October 22nd, 2018

    MORE:

    Pass Leader 100-105 dumps FYI:

    drive.google.com/open?id=0B-ob6L_QjGLpZHliX0lUeE1Ccms

    (649q~~~NEW VERSION DUMPS!!!)

    Good Luck!!!

    (p.s. Copy the upper link and open it in your browser.)

  11. Robert Milner
    October 22nd, 2018

    More:

    Pass Leader 200-105 dumps FYI:

    drive.google.com/open?id=0B-ob6L_QjGLpUTVNc3otMV8xMkU

    (539q~~~NEW VERSION DUMPS!!!)

    Good Luck!!!

    (p.s. Copy the upper link and open it in your browser.)

  12. Haina
    October 22nd, 2018

    Hi can anyone confirm about the dnd of control and data plane. There is a conflict in Chinese and 9tut dumps. I am about to take an exam within an hour

    (Chinese Dumps)
    Control Plane
    Filtering
    Routing State Exchange
    Establish Telnet Session

    Data Plane
    Qos
    Device Access
    Data Encapsulation

    As per 9tut

    Control Plane
    Device Access
    Routing State Exchange
    Establish Telnet Session

    Data Plane
    Qos
    Filtering
    Data Encapsulation

Comment pages
1 248 249 250 2815
Add a Comment